Fitting a snorkel to our Landcruiser

My partner Dixie fitted a snorkel to our 100 series Landcruiser. I must admit I was a little nervous when I could hear drilling coming from outside. Then my two year old ran inside and said “look what Daddy is doing, he is putting holes in the car”. Shh don’t tell but I was thinking to myself maybe a professional should be doing this. Turns out I had nothing to worry about as he did a great job.

Anyway I will let Dixie explain the process of fitting the snorkel.

Benefits of a snorkel

We decided to fit a snorkel to our 4wd.  There are a few benefits to fitting a snorkel and they relate to dust, water and air.  By raising the height of your air intake reduces dust going into your air filter and reduces the risk of water ingestion, water can be detrimental to a diesel engine.  The third benefit is cooler air into your engine.

Equipment needed to fit the snorkel

Most snorkel kits will come with everything required for fitting including template, bolts and instructions, obviously excluding hand tools etc.  You may need things like a power drill, hole saw, step drill, masking tape, marker pen, touch up paint and general tools.  I would recommend a battery powered drill as hole saws like going slow through steel.

equpiment

Fitting the snorkel

I started by removing the air box from the engine bay and the plastic inner guard from the wheel arch to access inside the panel.  Using masking tape I attached the template to the panel making sure it is in the correct position.  Using a permanent marker pen mark the panel through the holes in the template.  I then removed the template and used the masking tape to cover the panel around the areas being drilled including where the upper bracket goes.  This may prevent accidentally scratching the panel with a slip of the drill or hand tools.

Next is the scary part, drilling holes in your panel.  Using a small pilot drill, about 4mm, drill all the marked holes.  Then using the step drill I drilled all the holes out to 16mm as specified in the instructions, with the exception of the large hole and the A pillar.  With our particular snorkel it requires a 114mm hole saw for the large hole.

landcruiser-holes

Take off all the sharp edges of the holes, inside and out, using a deburring tool or whatever you have on hand.  The next step was to bolt the upper bracket onto the snorkel and temporarily place the snorkel on the car. Using your maker pen, mark where the upper bracket sits on the A pillar.  Remove the bracket from the snorkel & mark where the screws should go in the A pillar.  Drill the upper bracket holes & take off the sharp edges.

Use touch up paint to cover all exposed steel and let dry before installing the snorkel as per instructions.  The 16mm holes seemed excessively large, but I guess they allow for any slight error in the drilling or marking out positions.  The process took about 3 hours including distractions.

Snorkel Fitted.JPG

Don’t be afraid to have a go yourself.

If you want to keep up with what is happening on Let Me Be Free you can follow on Instagram here and Facebook here.

Advertisements

15 thoughts on “Fitting a snorkel to our Landcruiser

    • He is always doing stuff to the car and he gets annoyed at me cause I always say maybe we should get a professional to do that! (nothing like stirring the pot). He has never let me down so maybe he does know what he is doing after all.

      Like

  1. This is totally something my other half would attempt as well. He fitted a new set of dual batteries just recently. It was handy growing up with an uncle that was an auto-electrician!

    Like

    • Dixie fitted our dual batteries as well and he has pretty much done all the alterations to our car plus servicing. If we break down in the middle of nowhere at least we both know we are in safe hands!

      Liked by 1 person

  2. Granted my car knowledge goes as far as “most have 4 wheels” (I’ll never forget seeing 3 wheeled cars in the UK as a kid) but I don’t think I could ever drill into my own car! I’d be far too scared of my own incompetence 🙂

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s